Industrial Project Services
- Setting out plans
- Statutory approval drawings
- Elevation and sections of all the production building for proposal from PEB vendors
- Elevations and sections of all utilities
- Checking of PEB drawings
- Doors and windows schedules
- Road detailed sections & storm water drain details
- Final drawings
STRUCTURAL DESIGN SERVICES OFFERED
- STRUCTURAL DESIGN OF PROJECT FROM SCHEMATIC TO FINALIZATION
- CIVIL AND INFRA STRUCTURAL ENGINEERING
- VALUE ENGINEERING
- TECHNO-COMMERCIAL ENGINEERING
- REHABILIATION AND REPAIR STRUCTURAL CONSULTANCY
- HIGHWAY BRIDGE STRUCTURAL DESIGN
- MONORAIL STRUCTURAL DESIGN
- WATER TREATMENT PLANT STRUCTURAL CONSULTANCY
- SUBWAYS STRUCTURAL DESIGN.
- AIRPORT,JETTIES AND SEZ.
- ISSUE OF CONCEPT DRAWINGS OF PROJECT.
- ISSUE OF SCHEMATIC DRAWINGS OF PROJECT.
- ISSUE OF GA DRAWINGS FOR APPROVAL BY ARCHITECT.
- BAR BENDING SCHEDULE & QUANTITY OF MATERIAL.
- VALUE ENGINEERING TO OPTIMIZE THE COST OF PROJECT.
- TECHNO-COMMERCIAL FEASIBILITY OF PROJECT.
- SITE VISIT FOR CHECKING OF REINFORCEMENT BEFORE CASTING.
- TECHNICAL SUPPORT TO SITE PEOPLE IN CASTING OF COMPLEX STRUCTURE.
- STRUCTURAL AUDIT OF THE PROJECT.
- STRUCTURAL PEER REVIEW OF THE PROJECT
- Master plan with area calculations
- Elevations and sections for PEB vendors
- Specifications for PEB building
- Floating and collecting tenders from PEB vendors
- Evaluation of PEB vendors
- BOQ for civil work
- Tender for civil work
- Floating and collecting tenders for civil work
- Evaluation of tender
- PO/WO for building
Electrical Supply
- Calculation of total connected load, maximum demand and transformer capacity
- Calculation of cable sizes & lightning protection system
- Overall single line diagram, MV circuit breakers, transformer, Main LT panel and connections to all electric cabinets
- Floating of enquiry/tender
- Evaluation and finalisation of electrical equipment
Humidification
- Assessment of climatic conditions
- Heat load calculation
- Capacity of humidification plant
- No of air changes required
- Designing of supply air ducting and return air ducting
- Floating enquiries for humidification plant
- Floating enquiry / tender for ducting
- Evaluation and finalisation of humidification plant and ducting supplier
Compressed Air Supply
- Requirement of compressed
- Capacity and type of compressor
- Layout of compressor with dryer and filter
- Designing of compressed air line
- Floating enquiry/tender for piping
- Evaluation and finalisation of compressor and air pipe supplier
Water Supply
- Calculation of water requirement
- Capacity of the water storage and fire tank
- Water treatment plant
- Layout of the water tank and pump room
- Designing of water line
- Floating enquiry / tender for piping
- Evaluation and finalisation of water pipe supplier
Steam Supply
Thermic Fluid Supply
- Calculation of thermic heat requirement
- Capacity of thermic heater
- Layout of thermopac and fuel handling plant
- Designing of oil supply line
- Floating enquiry for Thermopac
- Floating enquiry / tender for piping
- Evaluation and finalisation of Thermopac and piping supplier
Effluent Treatment Plant
- Characteristic of effluent
- Quantity of effluent
- Water balancing
- Flow diagram
- Design parameter for treatment at each stage
- Layout of the effluent treatment plant
- Floating enquiry / tender for ETP
- Evaluation and finalisation of ETP
Sewage Treatment Plant
- Characteristic of sewage
- Quantity of sewage
- Design of sewage treatment
- Floating enquiry / tender for STP
- Evaluation and finalisation of STP supplier
- Calculation of total connected load, maximum demand and transformer capacity
- Calculation of cable sizes & lightning protection system
- Overall single line diagram, MV circuit breakers, transformer, Main LT panel and connections to all electric cabinets
- Floating of enquiry/tender
- Evaluation and finalisation of electrical equipment
- Assessment of climatic conditions
- Heat load calculation
- Capacity of humidification plant
- No of air changes required
- Designing of supply air ducting and return air ducting
- Floating enquiries for humidification plant
- Floating enquiry / tender for ducting
- Evaluation and finalisation of humidification plant and ducting supplier
- Requirement of compressed
- Capacity and type of compressor
- Layout of compressor with dryer and filter
- Designing of compressed air line
- Floating enquiry/tender for piping
- Evaluation and finalisation of compressor and air pipe supplier
- Calculation of water requirement
- Capacity of the water storage and fire tank
- Water treatment plant
- Layout of the water tank and pump room
- Designing of water line
- Floating enquiry / tender for piping
- Evaluation and finalisation of water pipe supplier
- Calculation of thermic heat requirement
- Capacity of thermic heater
- Layout of thermopac and fuel handling plant
- Designing of oil supply line
- Floating enquiry for Thermopac
- Floating enquiry / tender for piping
- Evaluation and finalisation of Thermopac and piping supplier
- Characteristic of effluent
- Quantity of effluent
- Water balancing
- Flow diagram
- Design parameter for treatment at each stage
- Layout of the effluent treatment plant
- Floating enquiry / tender for ETP
- Evaluation and finalisation of ETP
- Characteristic of sewage
- Quantity of sewage
- Design of sewage treatment
- Floating enquiry / tender for STP
- Evaluation and finalisation of STP supplier
MEP & Building Services
- Analysis of Heating and cooling loads, building envelopes and shading factors.
- Air conditioning system – air cooled and water cooled chillers, chilled water and DX type etc.
- Optimised Plant and Equip. selections
- Plant room layouts
- Schematics drawings of chilled water, condenser water system, cooling towers etc.
- Basement ventilation and exhaust system
- Air Treatment & Air Distribution system
- Smoke Extraction & Pressurisation System
- Kitchen & Toilet Exhaust
- Heat Recovery & TFA.
- VAV, VFD
- District Cooling & Thermal System.
- Radiant Cooling/Heating,Chilled Beams
- Humidification and Dehumidification.
- Thermic oil piping, compressed air, PNG/LPG
- Medical Gas System
- Flue Duct, thermo pack
- Duct collectors and Separators.
- Hot Gas Energy Recover.
- Economiser and Preheater etc.,
- Electrical Load Estimation
- Receiving Station and Substation Design
- Transformer Selection and Sizing.
- D.G. Sets, AMF Panel
- Gas Power Plant and Co-Generation System.
- Power Distribution (HT/LT)
- Lighting Design with software
- Voltage drop, Shor circuit calculations
- cable sizing and Breaker sizing and Bus Ducts.
- Switch Gears and Panels
- Distribution Boards
- Medium and Low Voltage and High voltage cablings.
- Earthing systems
- Lightning Protection System & Aviation Lighting System.
- UPS & battery system
- Emergency Lighting system,
- Power factor correction systems
- Code Compliance analysis.
- Solar Power Plants and Distribution & Solar Lighting
- Fire water capacity Assessment
- Sprinkler & Mist system
- Hydrant system
- Deluge Valves and Water Curtains
- Drencher system
- Fire Extinguishers
- Fire Pumps
- Code compliance Assessment
- Any other services relevant to this section shall be undertaken on case to case basis.
- Fire alarm system
- Public Addressing system
- VESDA system
- Gas Based Fire suppression system
- Foam based fire suppression system
- Water leak detection systems
- Any other services relevant to this section shall be undertaken on case to case basis.
- Estimation of Water Demand for Domestic, Flush water
- Water supply piping design(hot water , domestic , flush water cold water )
- Water tanks sizing
- Storm water system
- Rain water System and cross checking Geologist suggest RWH system.
- Sewage & ETP System.
- Water Treatment Plant.
- Geysers and hot water system.
- Boiler & Hot water, steam system
- Heat recovery system
- Medical gas, vacuum etc.,
- Structured cabling solutions (Passive )
- MATV cabling system ( passive)
- FTTH,DTH
- Telephones and data (passive)
- Auto paging and auto dialler system
- Nurse calling System
- Access control Door system
- CCTV System
- Any other services relevant to this section shall be undertaken on case to case basis.
- Man machine interface
- Field level devices
- DDC panels
- Cabling and wiring
- Automation of all MEP services and its integrations
- HVAC, electrical ,plumbing and fire fighting, fire alarm controls and integration all MEPF system
- Report Generation system
- Any other services relevant to this section shall be undertaken on case to case basis.
You as a client, the first Question you need to ask is whether you are wanting a simply a Drafter or a Professional Designer who delivers end product as a Designed Model unlike just a Model without design integrity and responsibility. Yes We are Design Firm with 20+ Rich years of Design consulting and Execution Back Ground. We do not simply transfer lines to 2D or 3D which is simply a duty of a draftsman While we give lively 3D designed Model which is workable and we are responsible for what is drawn because we designed the every smallest element of the product and the model. We deliver Live Model with full of Life which you can keep with you for the life time of the building exactly as It has been constructed. This will help you walk through at any point of time you want to do any change or showcase it to your clients, buyers, investors, tenants, Stake holders who are remotely located in any part of the worlds, want to transfer property to future buyers still you can do it without any hassles. After all its your property and you should know and have every detail of it any point of time of life of the building/property without going back to architects, Engineers etc., If you agree to above, then Engage us without a second thought, we will design from the scratch and handover till as-built. Remember with at the safe hands…… we are with 20+ years of Rich Design Experience. From Now, when you are with us, Then You are never with Simply Drafters…. We can provide three Dimensional Building Information Modelling through Autocad Revit software. The BIM enabled design and solution will provide seamless visualisation in a perfectly co-ordinated manner , accurate design, clash free classification and placement of mep services in conjunction with architectural , structural elements of the project well in advance. This will lead to elimination of site issues, clashes , variation in elevation issues, clear height justification, elimination of rework or change in direction or modification works which amounts to loss of time, reworking cost, missing of dead lines of project completion etc.,
“The following services currently we cover under Autocad Revit,
- Architecture
- Structure
- MEPF which are further divided as,
-Mechanical & Hvac,
-Plumbing
-Fire Fighting
-Electrical services
-Low Voltage - Miscellaneous MEP services
“BIM OUTSIDE CCE AS SIMPLY BIM MODELLERS,
We also undertake BIM-MEP Revit works for outside CCE project Too (Where CCE is not the mep consultant but still we can take up MEP Revit works) like,
- TO CONTRACTORS
- TO BUILDERS/DEVELOPERS
- TO HOME OWNERS
- TO INDUSTRIALISTS
- TO MASTER PLANNERS & URBAN DESIGNERS
- TO GOVT AUTHORITIES
- TO PRIVATE PARTIES
- TO ANY OTHER END USERS.
- TO PROVIDE BIM SERVICES TO ANY COUNTRY
| SL.NO. | LEVEL OF DETAILING | STAGE COVERS |
|---|---|---|
| 1 | LOD 100 | PREDESIGN/CONCEPT |
| 2 | LOD 200 | SCHEMATIC DESIGN |
| 3 | LOD 300 | DETAILED DESIGN DEVELOPMENT |
| 4 | LOD 400 | CONSTRUCTION DOCUMENTATION |
| 5 | LOD 400 | CONSTRUCTION |
| 6 | LOD 500 | ASBUILT |
Project Management
- Preparation of Project Schedule
- Creating Formats of Reporting
- Pre-qualification of third party consultants and vendors in a competitive bid process
- Proposal documentation, floating of enquires, evaluation and recommendation
- Advice Client on contracting terms and conditions
- Coordinate with Architect, Contractor and clients team
- Review Project document
- Monitor Progress of the project
- Contractor selection and award of contracts
- Evaluate, recommend for approval and process payment application
- Prepare measurement sheet as per actual work done
- Gather all the final invoices and submit for payment
- Close out all the vendors, consultants and contractors
- Monitor quantity, time, cost and cashflows
- Mediate and resolve construction conflicts
- Preparation of Project Schedule
- Creating Formats of Reporting
- Pre-qualification of third party consultants and vendors in a competitive bid process
- Proposal documentation, floating of enquires, evaluation and recommendation
- Advice Client on contracting terms and conditions
- Coordinate with Architect, Contractor and clients team
- Review Project document
- Monitor Progress of the project
- Contractor selection and award of contracts
- Evaluate, recommend for approval and process payment application
- Prepare measurement sheet as per actual work done
- Gather all the final invoices and submit for payment
- Close out all the vendors, consultants and contractors
- Monitor quantity, time, cost and cashflows
- Mediate and resolve construction conflicts
- Check Quality of work
- Check the execution of work as per design
- Site meeting to resolve the conflicts
- Suggest changes or modification in designs and execution items
Infrastructure Development Services
- Identify the requirement of buildings, roads, greenery and utilities
for project - Coordination for engineering design of water supply, drainage and sewage disposal, electrical, firefighting,
- Concept designing as per urban design guideline
- Preparation of submission drawings for approval
- Designs of roads
- Designs of culverts
- Design of storm water drainage and rain water harvesting
- Electrical System Designing
- Water Supply System Designing would include the following:
- Fire-fighting designing:
- Depending on the overall master plan prepare a comprehensive
landscaping design. - Prepare the specifications and would float the tender to various
suppliers
- Assessment of existing infrastructure
- Identify the new requirement for expansion
- Identify requirement for Infrastructure Modernisation
- Prepare designs and drawings for expansion or modernisation
Project Methodology
Design Approach
- We approach every project as unique project and provide cost effective, functional, sustainable by design, and code compliant solution suitable for that project in line with clients specific input parameters.
- We add values in all phases of the project
- We deliver our deliverables in line with the requirement of the project.
- To get all services under one roof
Methodology
- Concept design
- Schematic design
- Detailed Design development
- Tender documentation & award of contracts
- Construction co-ordination
- Commissioning, testing & handover procedure
Concept Design
- Setting design criteria & objectives
- Highlighting site constraints and services requirements
- Assessment of primary demand and consumption –cooling load, electricity, domestic, flush & fire water requirements & sizing of tanks. Providing alternates as applicable.
- Building envelope issues and shading parameters
- Outline SLD of distribution of major building services
- Statutory code requirements analysis W.R.T the given application and plans (in terms of both local bye-laws and international codes)
- Plant & equipment sizes and locations and its space allocation.
- Submission of design basis report with major preliminary single line diagrams and layouts with requirements of cutouts, shafts, services spaces etc.,
- On production of basic dbr and it schemtics, it is expected that client and all concerned agencies gives the approval to cce and then cce will proceed further to the next stage of schematic design.
- The same dbr and its schematics can be well used for submission to authorities like moef, hrc, green building if and as applicable etc.,
Schematic Design
- This is extension of the concept approved DBR and its schematics.
- Preparation of single line diagram for the layouts services and vertical schematics without sizing is done here and sent for approval
Design Development
- Detailed design calculations as per the parameters set in the DBR, client’s design guidelines if any. Doing the necessary co-ordination with architects and other consultants as per need.
- Detailed layouts for all services with all dimensions, sizes, capacities of equipment, typical connections, mounting and termination, distribution details
- Detailed single line schematic diagrams with all sizes and specifications
- Detailed plant room and equipment layouts with dimensions and expected sizes of equipment with associated operating loads for structural consultant design.
- Preparation of all relevant data sheets for equipment.
- In case any third party consultant is not appointed at this stage, then the layout shall be done for the services part with necessary assumptions whatever best we know from our past experience for the tendering purpose.
- Approval of above said drawings by the client for getting into the next stage.
Tender Documentation and Award of Contract
- Preparation of tender specifications in conjunction with the detailed design drawings
- Bill of materials
- General conditions of contract (this is generally a client scope however we can assist to provide the same)
- Estimates for the given bill of materials based on rates obtained from our recent projects awarded.
- Approval of tender documents, BOQ, GCC by the client.
- Floating of tenders and receipt of same by the client.
- Making necessary technical comparison and send it to project managers to further carrying on the commercial discussion with the services contractors.
- Attending tender negotiation meeting and providing necessary clarifications and assisting client to finalise the successful contractor for the services as required from the technical point of view of services.
Hand Over
- Approving as built documents & drawings prepared by the services contractors.
- Approving operations and maintenance manual prepared by the contractors
- Handing over the approved as built drawing and O&M manual to the client(both soft and hard copy).
- Assisting the client in stabilizing the system along with the service contractors for perfect functioning wherever necessary.
Construction Stage
- Briefing the services contractors during the kick-off meetings to start commencing the works at site from the services point of view.
- Attending scheduled site co-ordination meetings (as mutually agreed) and providing necessary clarifications as and when required in the form of sketches etc.,
- Approving shop drawings produced by contractors.
- Assessing quality of works being executed and providing necessary corrective measures in line with the tender specifications & BOQ.
- Recording changes suggested and circulating it to all.
- Assisting clients in major equipment inspection at factory as mutually agreed or the test results can be approved as the case applicable.
- Approving commissioning parameters as recorded by vendors with project managers.